your personal cnc Designer

Divers

ve seen similar designs on other masks to make them more comfortable I've only tried this for one night, and at this point and it made a huge difference !. Just make sure you clamp it on the free end of the strap so it can move and not dig into your head. Enjoy :). Update, I found the old design a little l

ResMed FX mask hose clamp
I created a new and improved version of this turntable. The new version uses an Arduino Uno, stepper motor, 1602 LCD screen and a 9g servo motor. The turntable is now able to automatically take photos 360 degrees around which can be turned into a 3D-model using photogrammetry software. You can check it out here

Fully 3D-printable turntable
Low profile filament spool holder, for when you want your filament sitting next to your printer, and don't take up a lot of space.

Filament Spool Holder - Bearings and custom width
This shelf bracket was designed to use the shelves and sides from a flat pack bookcase as shelving for the garage. The bracket is 194mm long and 25mm thick with holes to fit 4mm countersunk wood screws.

Shelf Bracket 195mm
These console risers are intended to lift an original Xbox one safely above a Playstation 4. When your entertainment center is crunched for space, placing the PS4 on top of the Xbox one may seem like the obvious solution...WREHNG! Most of the air vents on the Xbox are directly on top and blocking those is begging for you console to overheat.

Xbox One Riser
ELEFANTE GEOMETRICO EL MEJOR DISEÑO

ELEFANTE GEOMETRICO LOW POLY
3D printable Massage roller for your feet or noted muscles.

massage roller
Belt tensioning modification for Anet A8, hesine, senhai, omni, m505 3d printer. WARNING!!! this will stretch the belts! you need to upgrade them to fiberglass reinforced belt. stretched belt will cause your print to be bigger in dimensions. use M4 hex head screws and nuts for tensioning knobs. which is readily available at Home Depot or Lowes. 25mm length bolt for y axis, 50mm for x axis. x utilize thumb nut, y utilize thumb screw. two M3 allen head bolts are to put the pressure on x axis rods, rather than on the z carriage which will put force on the z axis rods. adjust it so that there would be about 1mm gap between z carriage and the bridge part. you may want to install my frame braces before putting too much tension on y belt, or the acrylic frame can crack from pressure. for x belt, the photo shows anti z wobble modification, but it is not needed for belt tensioning.

Belt tensioning modification for Anet A8
Largely inspired from ldabkey, this paper towel holder fit a 25mm diameter rod or tube (like a piece of broom handle, which is what I used). Fits a pegboard with 4mm hole diameter, 25.4mm/1inch holes distance, 3mm tickness. STEP file included.

Pegboard Paper Towel Holder for 25mm rod
Designed a shelf really quick to display printed parts and get them off of my desk... Instructions 1/16th inch Poly carbonate cut to 5x12 inch. designed to slide in to grooves. Drywall screws for mounting

Display Shelf - low capacity
There are 4 different lengths : 19, 21, 23 and 25cm. For each one of these lengths you have 3 widths : 9, 10 and 11cm

Shoes Organizer (Multiple sizes)
Meow! Simple fridge magnet, designed for x2 3mm³ magnets. Printed at 200μm, colour change for the final 2 layers.

Simon's Cat fridge magnet
Update 11/5/18: Added 1.5mm base to the thick version. Update 11/4/18: Added a thick version (+2mm thickness). Update 3/11/17 : New hole, added fillet. Update 10/23/16 : increased thickness for screw holder and legs. A simple, adjustable belt tensioner + a belt tie to replace the cable tie. The tensioner requires an M3 screw. The screw hole is tight-fit and should provide more than enough tension to hold the screw. Designed to be printed at 100% scale. Use higher wall line count (shells) & high infill for maximum strength.

Adjustable Belt Tensioner/Tightener and Belt Tie (Tevo Tarantula)
A handle and label system for IKEA ALEX drawer units. It uses a fixed handle and swappable labels. You can use the Thingiverse customizer to generate your own labels with custom text / text dimensions / fonts / etc. I have also added a Braille option to create labels for people with a visual impairment. If there are any features you want to see added in the label customizer please let me know in the comments and I will try to add them.

IKEA ALEX Handle & Label System
You'll need some M3 nuts and M3 screws for the clamps. I'm pretty sure the screws are 3M 12mm. Have a look at the pictures for the result. The design is based off of another design but has been heavily re-designed to suit my purposes.

CNC PCB Holder
Laser cut Giraffe Wooden Animal Head dxf File

Laser cut Giraffe Wooden Animal Head dxf File
This is my final model of 2017 and the 3rd model I've released this week - which is a record for me. This is a Christmas Tree bauble with screw top which allows the hollow to act as a container (for little gifts/secrets).

Christmas Tree Bauble (with secret compartment)
Same as Fish Bone Wall Hanger but the hooks decided up in separate parts. This way you can print as many as you want and build up your own fish with the modules.

Fish Bone Wall Hanger - Modular Version
A sword pin that uses the tack from a thumbtack! modeled after a claymore. printed at .01mm layer height at %100 infill. Enjoy!

Sword Pin!
Everyone needs a purpose, including a Cute Octopus! Instructions UPDATE I uploaded an obj file just to see if a different file format will helps those having issues. I remixed with Cheetah3D, and printer on a MakerBot Replicator 2, with MakerWare. I used the STANDARD setting with defaults. I've printed several times with no issues.

Cute SDCard Holder
If your nozle diameter is 0.4mm, set your extusion width 0.45mm to avoid zig-zaging behavoir on wall construction and reduce overall print time.

Drawer for Ender3, Ender 3
I use double sided transparent 3M tape to attach this to a book case, works very well.

Spray paint can holder
A remix of ffleurey's corner guard (http://www.thingiverse.com/thing:139473) but without the bottom stop so you can use it on a wider variety of furniture. Please note: These have not been formally certified or tested so do not have any expectations about the level of formal protection from this design. If you think it will work for you use it. Instructions Should be easily printable on just about anything.

Furniture Corner Guard for Child Safety
A pocket screw jig for standard sized pocket screws and drill bits. Adjustable height for different thicknesses of wood (from 0.75" to 1.5" thicknesses) NOTE: Designed for the tolerances of my printer (adding or subtracting between 1/64" and 1/32" for parts to slide across each other) Solidworks files included. Feel free to edit to your liking.

Adjustable Pocket Screw Jig