your personal cnc Designer

Outils artistiques

It is a support for clips that hold objects for painting or drying. Perfect for hobbyists and craftsmen. It is advisable to orient the model with the open holes resting on the print bed.

Painting stand
Paint rack x20 for Vallejo, The Army Painter, Andrea Colors, Green Stuff World, Scale75, Reaper Mini... bottle types. UPDATE v2: Internal supports with more resistance

Paint Rack x20
This is a stackable rack to hold your Testors Modelmaster paints. It is strong enough to stack several units high. The lids will fit into the bottom of the rack above to keep them stacked securely and you can read the labels. If your printer is tall enough you can print it with one of the ends on the bed and not use any supports.

Testors Modelmaster Paint Bottle Holder
This is a chain style can holder, you can connect them as much as you need. Move one side slightly up to make inclain that prevent the can from falling down (it works fine even if its level).

Spray-can holder
Simple stand for pens, pencils and so on. Inspired by cubistand Please be so kind and post your Makes. Would be very nice. ;)

Pencil Pen Brush Holder Stand
Reduced the diameter of the "pins" on which a paper roll is mounted. The old version was too close to the paper roll diameter and could result in tightening of the roll on the pins. Also improved the design of the screw knobs.

IKEA Paper Roll Holder
For construction of this model you will need: 5x 608 bearings 4x M5x15+ screw + 4xM5 nut 3x M3x 10,15, 20 + 3xM3 nut one M3 and one M6 spacer

Pantograph for scaling up using 608 bearings
jewelry tree for hanging necklaces and earrings

wooden tree for hanging jewelry
An updated version of my last knitting needle holder. I've adjusted the design so that it prints great without any supports. Make sure that the holes face down on the bed, for best results. I added a small angled pocket on one side to hold darning needles or small accessories. It makes a great gift for friends or family that like to knit/crochet.

Knitting Needle & Crochet Hook Holder V2
Simple Modern Paint Brush Stand. Print Settings Printer brand: MakerBot Printer: MakerBot Replicator 1 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Notes: Printed with PLA I used Simplify 3D for slicing. I did 20% on the fill for the whole project however depending on the speed you print at and the printer you are using the base and the main grid can take 3 hours to print but if sliced just right this can possibly be reduced. Notes: I printed the cubistand_rod_c.stl vertically on none heated bed with blue painters tape and a light touch of glue stick with no problems. Post-Printing Steps to glue the parts. I used RC Model glue to glue the rod to the base waited to dry for a few minutes then glued the main grid to the rod and laid the stand on it's side to let dry and finally I glued the top cap. Keep in mind one can print 4 rods and have on on each corner. I liked to keep the modern floating look.

Cubistand Pencil Pen Brush Holder Stand
This Is a Three-Tiered essential oil stand specifically for "Do Terra" brand oils though will fit bottles with a 28mm diameter. Designed for parts to be printed separately and glued together (this allows the design to be printed on a machine with 120mmx120mm bed size. You will require 3 of the centre shelves and 1 of the left and right sides to make a stand capable of holding 12 bottles. Vial stand pictured requires some modification before uploading but is designed to clip on to the side of the stand. (can be mirrored in slicer to attach to opposite side)

Essential Oil Stand
18 holes to use with brushes and 16 to the paints.

Paint & Brush Holder
A paintbrush holder for stopping paintbrushes from marking or rolling off the table. It is customisable so you can play with the dimensions and also the number of paintbrushes that it can hold. You can see more details at http://jweoblog.com/?p=277 Instructions Designed in OpenSCAD, printed on a RepRap Huxley in white PLA

Customizable Paintbrush Holder
This is my printable version of the classic etch-a-sketch / telesketch. A kind of plotter-toy. You can draw what you imagine rotating the X-Y knobs. It works great with a marker or a pen. The drawing area it's 15x10cms aprox. The X-axis acts moving the complete paper, inspired in the Prusa Y-axis (moving all bed) It has many parts and can print mostly without supports (i hate supports) I've arrange the parts in 6 files according to impression parameters and print order. Included a PDF with assemblig instructions and some tips. Included a ZIP file with al the STL files for each part. Also included the 123D Design files.

micro-sketch
Laser Cut Wooden Axe for wall or desk decoration

Wooden Axe